Where do these go?

Where all the workshop knowledge lives together.
Post Reply
VTR Phoenix
Posts: 710
Joined: Sat Jan 16, 2016 12:07 pm
Location: Slough, Berkshire

Where do these go?

Post by VTR Phoenix »

have been searching filches for what seems like forever but don't know where these parts go. As I got the storm in bits and nothing was labelled up I am a little lost. Can anyone help?

This I believe goes on the front carb sync nipple?

Image

These I know are cable/wire tidies but where do they mount?

Image

The rest I do not have a Jimmy choo

Image

Image

Image


Any help in finding out where these go is greatly appriciated
If it aint broke, get your bloody hands off it!
User avatar
Ckennedy
Posts: 3560
Joined: Tue Jul 10, 2012 9:57 pm
Location: Leicestershire

Re: Where do these go?

Post by Ckennedy »

I belive your right with the 1st pic.

The 2nd pic where you have no clue o believe are clips that fit under the seat but they normally get removed to make getting the seat on and off easier.

The 3rd pic, look like belly pan brackets which mount around the sump using the sump bolts.

The other bits I'm not to sure on but someone will know more and or correct anything I've said

Sent from my SM-A300FU using Tapatalk
VTR Phoenix
Posts: 710
Joined: Sat Jan 16, 2016 12:07 pm
Location: Slough, Berkshire

Re: Where do these go?

Post by VTR Phoenix »

Ckennedy wrote:I belive your right with the 1st pic. I shall fit this tomorrow

The 2nd pic where you have no clue o believe are clips that fit under the seat but they normally get removed to make getting the seat on and off easier. If that's the case I wont worry about those

The 3rd pic, look like belly pan brackets which mount around the sump using the sump bolts. That might make sense as I have two fitted already as per the parts filche I looked at but they didn't seem substantial enough to hold a full size belly pan.

The other bits I'm not to sure on but someone will know more and or correct anything I've said

Sent from my SM-A300FU using Tapatalk

Thanks CK
If it aint broke, get your bloody hands off it!
User avatar
popkat
Posts: 2804
Joined: Sat Apr 28, 2012 9:32 am
Location: Devon

Re: Where do these go?

Post by popkat »

Picture 2 - cable guides up by headstock I believe (I'll try to remember to look at mine tomorrow)

Picture 3 - doesn't look like a bike part.

Picture 4 - Seat mounting brackets, fit to the seat and hook into subframe at front of pillion seat area.

Picture 5 - aftermarket belly pan/fairing lower brackets


.
http://www.bidefordmotorcycles.co.uk
2014 CRMC Post classic Superbike champion.
2014 CRMC Post classic senior production champion. On a Suzuki Katana 1100
My bikes, Firestorm, Suzuki GSX-s1000 Katana, VFR800Fi. Projects, 1986 popup Katana, 3 XJ600’s
VTR Phoenix
Posts: 710
Joined: Sat Jan 16, 2016 12:07 pm
Location: Slough, Berkshire

Re: Where do these go?

Post by VTR Phoenix »

Cheers popkat, do you think I will need the seat brackets?

I know one of the tidys fits under the seat (the larger of the two) and I'm sure the smaller one possibly has the clutch line run through it? but not sure exactly of the mounting points.
If it aint broke, get your bloody hands off it!
User avatar
lloydie
Posts: 20920
Joined: Mon Jan 17, 2011 11:16 pm
Location: In the garage somewhere in Coventry

Re: Where do these go?

Post by lloydie »

Image
The small one fits on the left of the head stock holding the loom and clutch pipe .
The big one holds the loom on the inner rear part of the main frame on the left side
User avatar
TravisZack
Posts: 457
Joined: Mon Feb 17, 2014 9:48 am

Re: Where do these go?

Post by TravisZack »

Edit: Lloydie beat me to it but...

Pic 2 are cable stays. Found some pics from my rebuild:

Little one. Up by the headstock, clutch goes through the grommet.

Image

Big one. Inside the left side of the frame by the back of the rear cam cover.

Image
VTR Phoenix
Posts: 710
Joined: Sat Jan 16, 2016 12:07 pm
Location: Slough, Berkshire

Re: Where do these go?

Post by VTR Phoenix »

Lloydie, Travis you two are saints and those pics are perfect, loom is all over the place at the moment so after a few hours lip I'll set to tidying it up.
If it aint broke, get your bloody hands off it!
StuartWags
Posts: 974
Joined: Mon Nov 14, 2011 2:00 pm
Location: Whaplode Drove, Lincolnshire

Re: Where do these go?

Post by StuartWags »

The after market belly pan brackets i think are for this type belly panImage
User avatar
sirch345
Site Admin
Posts: 21672
Joined: Mon Aug 25, 2003 10:35 pm
Location: The West Country.

Re: Where do these go?

Post by sirch345 »

As Ckennedy says, these brackets are under seat brackets,

Image

Image




These brackets definitely look like Powerbronze lower fairing brackets as StuartWags says, although there should be three in total.

Image

You can see where they go in this link where I have posted photos:-
http://www.vtr1000.org/phpBB3/viewtopic ... ts#p380004

Chris.
VTR Phoenix
Posts: 710
Joined: Sat Jan 16, 2016 12:07 pm
Location: Slough, Berkshire

Re: Where do these go?

Post by VTR Phoenix »

Thanks a million guys, you have all been a godsend. All parts now fitted, except the bellypan brackets as will have to mod those but only have the two although I do (as per the filche) have the standard belly pan brackets as well so I'm sure I can sort something as the one I've got has no predrilled fixing points so I think work with what I have.
If it aint broke, get your bloody hands off it!
User avatar
MacV2
Posts: 17418
Joined: Sun Jan 21, 2007 12:07 pm
Location: Grain

Re: Where do these go?

Post by MacV2 »

''Where do these go?''

In the bin if you cant find where they go...Hope that helps.
Making up since 2007, sometimes it's true...Honest...
VTR Phoenix
Posts: 710
Joined: Sat Jan 16, 2016 12:07 pm
Location: Slough, Berkshire

Re: Where do these go?

Post by VTR Phoenix »

That will be what's happening with the rest of the parts box I got with it when I'm finished
If it aint broke, get your bloody hands off it!
Post Reply