Badly corroded exhaust clamp

General Bike chat
User avatar
Wicky
Posts: 6809
Joined: Sat Feb 11, 2006 2:43 pm
Location: Colchester Essex
Contact:

Re: Badly corroded exhaust clamp

Post by Wicky » Wed Jan 03, 2018 11:22 pm

Thread resurrection

Working on a little project to look at getting some custom made split flanges in stainless - can somebody please confirm these measurements

Image
It may be that your whole purpose in life is simply to serve as a warning to others.

User avatar
fabiostar
Posts: 4440
Joined: Sat Jun 01, 2013 2:53 pm
Location: sunny belfast

Re: Badly corroded exhaust clamp

Post by fabiostar » Thu Jan 04, 2018 8:13 am

Varastorm will have those measurments :D
the older i get,the faster i was :lol:

User avatar
Wicky
Posts: 6809
Joined: Sat Feb 11, 2006 2:43 pm
Location: Colchester Essex
Contact:

Re: Badly corroded exhaust clamp

Post by Wicky » Thu Jan 04, 2018 5:30 pm

Things are progressing. Confirmed they'll be able to 2D cut out in either mild steel or stainless

Looking at copying this design as suggested by KermitLeFrog in the previous page in the thread. I'm favouring making a fully stainless steel version - depending on what welder has to say - it'll cost a bit more than mild steel but longevity is the priority. Holes in the drawing will change into slots to account for width of the cuts, made after the tubes are welded on.

Image
It may be that your whole purpose in life is simply to serve as a warning to others.

User avatar
tony.mon
Posts: 12347
Joined: Wed Jul 25, 2007 9:46 pm
Location: Norf Kent

Re: Badly corroded exhaust clamp

Post by tony.mon » Sat Jan 06, 2018 5:40 pm

Wicky wrote:
Thu Jan 04, 2018 5:30 pm
Things are progressing. Confirmed they'll be able to 2D cut out in either mild steel or stainless

Looking at copying this design as suggested by KermitLeFrog in the previous page in the thread. I'm favouring making a fully stainless steel version - depending on what welder has to say - it'll cost a bit more than mild steel but longevity is the priority. Holes in the drawing will change into slots to account for width of the cuts, made after the tubes are welded on.

Image
Those will work fine, well done.
It's not falling off, it's an upgrade opportunity.

User avatar
fabiostar
Posts: 4440
Joined: Sat Jun 01, 2013 2:53 pm
Location: sunny belfast

Re: Badly corroded exhaust clamp

Post by fabiostar » Sun Jan 07, 2018 8:44 pm

nice looking job :thumbup:
the older i get,the faster i was :lol:

User avatar
Wicky
Posts: 6809
Joined: Sat Feb 11, 2006 2:43 pm
Location: Colchester Essex
Contact:

Re: Badly corroded exhaust clamp

Post by Wicky » Wed Jan 17, 2018 12:55 pm

Sent off revised drawing for kwacka style split flange - decided against the tube and bolt version as too much faffing about with extra material welding and cutting. This version can be simply cut out then sent for trimming (CNC?) to achive the interlocking pieces.

Image

Image

Image
It may be that your whole purpose in life is simply to serve as a warning to others.

User avatar
fatfreddy000
Posts: 105
Joined: Thu May 04, 2017 6:02 pm

Re: Badly corroded exhaust clamp

Post by fatfreddy000 » Wed Jan 17, 2018 3:06 pm

Wicky wrote:
Wed Jan 17, 2018 12:55 pm
Sent off revised drawing for kwacka style split flange - decided against the tube and bolt version as too much faffing about with extra material welding and cutting. This version can be simply cut out then sent for trimming (CNC?) to achive the interlocking pieces.

Image

Image

Image
that looks great,
a bit tidier than mine- i used a slit disc and angle grinder to achieve the interlock profile..
I've just got in from fitting it after ages buggering about with broken corroded studs..
i will post some info and photos now on the other thread..
“If all insects on Earth disappeared, within 50 years all life on Earth would end. If all human beings disappeared from the Earth, within 50 years all forms of life would flourish.” Biologist Jonas Salk

User avatar
Wicky
Posts: 6809
Joined: Sat Feb 11, 2006 2:43 pm
Location: Colchester Essex
Contact:

Re: Badly corroded exhaust clamp

Post by Wicky » Wed Jan 17, 2018 5:52 pm

Cheers - its still only at the drawing stage and a rough cardboard mockup like you made - the colour pics are of a similar type of flange for kwackas. Do the measurements match what you had as mine are still attached on a spare header.

Knew O'level TD would eventually come in useful for somefink after almost 40 years.

Loooking at an initial production run of 20 widgets. So that will do 10 bikes for 1 header or 5 bikes front & rear. Then possibly more if there's a demand.

Image
It may be that your whole purpose in life is simply to serve as a warning to others.

User avatar
fatfreddy000
Posts: 105
Joined: Thu May 04, 2017 6:02 pm

Re: Badly corroded exhaust clamp

Post by fatfreddy000 » Wed Jan 17, 2018 6:15 pm

Wicky wrote:
Wed Jan 17, 2018 5:52 pm
Cheers - its still only at the drawing stage and a rough cardboard mockup like you made - the colour pics are of a similar type of flange for kwackas. Do the measurements match what you had as mine are still attached on a spare header.

Knew O'level TD would eventually come in useful for somefink after almost 40 years.

Loooking at an initial production run of 20 widgets. So that will do 10 bikes for 1 header or 5 bikes front & rear. Then possibly more if there's a demand.

Image
i measured up originally to make a pair from scratch from a sheet of 8mm SS but with the lack of a workshop and just a grinder and drill i realised it would be tiresome and expensive to do- particularly holesawing 2 x 45mm holes 8mm deep through SS.
i just brought 2 plain mild steel 45mm x 8mm flanges as the blanks then cut out a section and the interlock profile as a cheap option.
would really like to do a better job and use SS but time and money are not overflowing at present.
the stud slots in the flanges i used are bit too wide apart and needed to be extended with a round file to match with the bosses on the VTR.
i made the distance between the stud centres approx 73mm.. nothing else (except header diameter) should matter within reason..
will yours be SS and do you have an idea of £/pair?
thanks mate..
“If all insects on Earth disappeared, within 50 years all life on Earth would end. If all human beings disappeared from the Earth, within 50 years all forms of life would flourish.” Biologist Jonas Salk

User avatar
Wicky
Posts: 6809
Joined: Sat Feb 11, 2006 2:43 pm
Location: Colchester Essex
Contact:

Re: Badly corroded exhaust clamp

Post by Wicky » Wed Jan 17, 2018 6:32 pm

i made the distance between the stud centres approx 73mm.. nothing else (except header diameter) should matter within reason..
will yours be SS and do you have an idea of £/pair?
I measured centre to centre 70mm exactly and laying up the cardboard prototype to the originals the holes match. Still awaiting a quote fom the laser cutters on producing them in SS. They can do either 6mm or 8mm thick. Then popping down to local college / or local engineering firm for finishing with a bands saw(?). So while price still unknown, things are progressing as the cutters also recieved a spare rear header with OEM flange attached I posted for them to see what I'm aiming for.
It may be that your whole purpose in life is simply to serve as a warning to others.

User avatar
sirch345
Site Admin
Posts: 16297
Joined: Mon Aug 25, 2003 9:35 pm
Location: Cornwall, UK

Re: Badly corroded exhaust clamp

Post by sirch345 » Wed Jan 17, 2018 11:10 pm

Wicky wrote:
Wed Jan 17, 2018 12:55 pm
Sent off revised drawing for kwacka style split flange - decided against the tube and bolt version as too much faffing about with extra material welding and cutting. This version can be simply cut out then sent for trimming (CNC?) to achive the interlocking pieces.

Image

Image

Image
Nice one Wicky, I definitely prefer this design 8)

Good luck with it,

Chris.
A closed mouth gathers no foot. :thumbup:

ImageImageImage

Post Reply