MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Need advice on which oil to use or which tyre best suits you? Share your topic and get help here.
Post Reply
User avatar
E.Marquez
Posts: 635
Joined: Wed May 30, 2012 1:27 pm

MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by E.Marquez »

GEN III MOSFET Kit now available. No more soldering, no old OEM wiring harness used.... All new cabling from RR to stator & battery
Gen III stator cable.jpg
(Note: cable is not in installed position)
new kit update.jpg
new kit update.jpg (40.77 KiB) Viewed 5798 times
(Note old kit pic , new Stator cable for the kit in the 1st pic)

Gen III Plug and play ready to install Superhawk MOSFET RR Kit FH020 ( 50 amp rated, and the VTR Alt output is MAX of 23.3amps @12VDC)
$153.00 shipped Priority mail in the US.

Easy, fast and complete, not a general fit kit that will have excess wiring you have to pile up someplace, but a kit that is designed to fit the Honda Superhawk perfectly.

Entire kit is pre-assembled. The installer only need remove old RR, bolt in place the new MOSFET RR, unplug the stator from the old wiring harness and plug in the new RR cabling provided. Add the charge cable ring terminals to your batter and your done, zip tie cabling in place, replace tail cowl and go ride. This kit will come with 6mm battery terminals found commonly on lead acid type batteries. If you want the smaller 5mm terminals used with some Li Ion batteries just ask at the time you order.
This kit replaces all of the known problems with the VTR charging system. Melted plugs, burnt wires, Diode RR, gaining increased charge voltage to the battery in the process. All protected in your choice of the available wire sheathing options, marine rated circuit breaker. No weak soldered joints all terminals are professionally crimped with the correct F and O crimps on wire / insulator with heat shrink tube stress relief on terminals where needed.
Marquez Motorcycle Services
Solutions to recurring maintenance
Race/Adventure ride event prep
Post event services

Total Rider
Your path to a TX motorcycle license
And advanced Rider training
User avatar
StormyRob
Posts: 1565
Joined: Sat Nov 07, 2015 7:33 am
Location: Northern Ireland. The place of legend

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by StormyRob »

Don't have a storm... At the minute. However I think it's great people are still making decent bits for this bike. Good work mate
If you don't try you never know if you can do it.
User avatar
E.Marquez
Posts: 635
Joined: Wed May 30, 2012 1:27 pm

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by E.Marquez »

StormyRob wrote: Fri May 17, 2019 11:40 pm Don't have a storm... At the minute. However I think it's great people are still making decent bits for this bike. Good work mate
Thanks mate

I enjoy making stuff for the old girls
E641418C-A1AC-4707-B955-8148F8DCF7D9.jpeg
That one just went to a guy in New Zealand
Marquez Motorcycle Services
Solutions to recurring maintenance
Race/Adventure ride event prep
Post event services

Total Rider
Your path to a TX motorcycle license
And advanced Rider training
User avatar
sirch345
Site Admin
Posts: 21669
Joined: Mon Aug 25, 2003 10:35 pm
Location: The West Country.

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by sirch345 »

Good work Erik :clap: :clap:

Ideal for owners who are not happy to carry out their own wiring, or who just want a plug and play (plus battery connections) MOSFET rectifier/regulator without all the hassle of wiring it in :thumbup:
You can't get much easier than that 8)

Chris.
User avatar
NY4600
Posts: 47
Joined: Tue Jun 07, 2016 7:18 pm
Location: Kongsberg, Norway

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by NY4600 »

Do you ship to Norway? :D
User avatar
E.Marquez
Posts: 635
Joined: Wed May 30, 2012 1:27 pm

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by E.Marquez »

NY4600 wrote: Sat Jun 01, 2019 9:58 pm Do you ship to Norway? :D
I've shipped to many non US locations, a Small island off Africa, Australia, Greenland, Austria and more..
shoot me a message at marquezmotorcycleservices@gmail.com with a full shipping address and I'll confirm shipping cost, but I would expect it to only add $28 USD to the base price
Marquez Motorcycle Services
Solutions to recurring maintenance
Race/Adventure ride event prep
Post event services

Total Rider
Your path to a TX motorcycle license
And advanced Rider training
User avatar
Fabiodriven
Posts: 36
Joined: Thu Aug 01, 2019 6:24 am

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by Fabiodriven »

Hola! I was hoping to have one of these shipped to 34480. I emailed you a couple of days ago, just waiting to hear back! Thanks!
User avatar
sirch345
Site Admin
Posts: 21669
Joined: Mon Aug 25, 2003 10:35 pm
Location: The West Country.

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by sirch345 »

Fabiodriven wrote: Sat Dec 28, 2019 4:29 pm Hola! I was hoping to have one of these shipped to 34480. I emailed you a couple of days ago, just waiting to hear back! Thanks!
He's probably on the Christmas break,

Chris.
User avatar
Fabiodriven
Posts: 36
Joined: Thu Aug 01, 2019 6:24 am

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by Fabiodriven »

Yup that's what I was figuring. Hopefully he's back in action soon! Thanks again Chris!
User avatar
E.Marquez
Posts: 635
Joined: Wed May 30, 2012 1:27 pm

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by E.Marquez »

What what who, when, whatdidImiss?

:D
Break? What the wombles sake is that?
Sorry mate missed the mail I guess
Please try again
marquezmotorcycleservices@gmail.com
Or FB message me at https://www.facebook.com/WeBuildAdventure/
Marquez Motorcycle Services
Solutions to recurring maintenance
Race/Adventure ride event prep
Post event services

Total Rider
Your path to a TX motorcycle license
And advanced Rider training
User avatar
E.Marquez
Posts: 635
Joined: Wed May 30, 2012 1:27 pm

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by E.Marquez »

Fabiodriven wrote: Tue Dec 31, 2019 6:37 pm Yup that's what I was figuring. Hopefully he's back in action soon! Thanks again Chris!
Got you on FB messaging now, Thanks
Marquez Motorcycle Services
Solutions to recurring maintenance
Race/Adventure ride event prep
Post event services

Total Rider
Your path to a TX motorcycle license
And advanced Rider training
User avatar
sirch345
Site Admin
Posts: 21669
Joined: Mon Aug 25, 2003 10:35 pm
Location: The West Country.

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by sirch345 »

E.Marquez wrote: Mon Jan 06, 2020 3:53 pm
Fabiodriven wrote: Tue Dec 31, 2019 6:37 pm Yup that's what I was figuring. Hopefully he's back in action soon! Thanks again Chris!
Got you on FB messaging now, Thanks
At last, well done :clap:

Chris.
User avatar
Fabiodriven
Posts: 36
Joined: Thu Aug 01, 2019 6:24 am

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by Fabiodriven »

Got my kit installed today and I'm extremely happy I ordered from Erik, because my wiring was roached! Thanks very much Erik! I would highly recommend this kit!!

Image
User avatar
E.Marquez
Posts: 635
Joined: Wed May 30, 2012 1:27 pm

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by E.Marquez »

Fabiodriven wrote: Sat Jan 11, 2020 8:24 pm Got my kit installed today and I'm extremely happy I ordered from Erik, because my wiring was roached! Thanks very much Erik! I would highly recommend this kit!!

Image
Your very welcome, and I am stealing that pic for my "this is why" folder
Marquez Motorcycle Services
Solutions to recurring maintenance
Race/Adventure ride event prep
Post event services

Total Rider
Your path to a TX motorcycle license
And advanced Rider training
User avatar
Fabiodriven
Posts: 36
Joined: Thu Aug 01, 2019 6:24 am

Re: MMS GEN III MOSFET kit NO WIRING WORK NEEDED

Post by Fabiodriven »

Absolutely! There were at least two wires completely disconnected, and almost all of them were burnt and corroded.
Post Reply