cb1300 wheels

[lanny]

Will SP2 and possibly CB1300 wheels fit the SP1 ?
I have noticed that CB1300 wheels look identical to SP2 wheels, does anyone know if they are the same ?
I like the gold wheels on the cb1300 and wonder if they would fit an SP1, although I don't think the abs wheels will .

[lloydie]

I like the cb13 5 spokes wheels I've asked a local beakers to lend me a set if he ever gets a set in so I can have a play :-)

[8541Hawk]

SP1 and SP2 wheels are interchangeable, no worries

As for the CB wheels, I don't know but would assume it is set up to run the smaller 25mm axle so you might need to source bearings and possibly spacers.

[leevtr]

I like the cb13 5 spokes wheels I've asked a local beakers to lend me a set if he ever gets a set in so I can have a play :-)

I've got a set.....attached to the cb1300 swingarm, frame, and engine !!

[lloydie]

When you get a chance could you take some measurements please

[Tweety]

SP1 and SP2 wheels are interchangeable, no worries

As for the CB wheels, I don't know but would assume it is set up to run the smaller 25mm axle so you might need to source bearings and possibly spacers.

Apart from that, they look pretty much identical, so it's entirely possible that they are so, despite different part-no... I'd say it's highly likely, as Honda is known to re-use things...

[leevtr]

When you get a chance could you take some measurements please

What do you need ?

[lloydie]

Front Spindle size.
Front disc size
Disc spacing (between the discs)

Rear
Outside Sprocket to out side disc.
Spindle size
Inside disc to wheel Centure and the same with sprocket .
Please no rush tho .

[MacV2]

Front Spindle size.
Front disc size
Disc spacing (between the discs)

Rear
Outside Sprocket to out side disc.
Spindle size
Inside disc to wheel Centure and the same with sprocket .
Please no rush tho .

Not much then...

While you at it Lee can you come round & cut me grass...

[leevtr]

Front Spindle size.
Front disc size
Disc spacing (between the discs)

Rear
Outside Sprocket to out side disc.
Spindle size
Inside disc to wheel Centure and the same with sprocket .
Please no rush tho .

Spindle sizes being thickness I assume ??

[leevtr]

Front Spindle size. The only bit I can get to without removing the wheel is the wider exposed end ( not the nut end ). 25mm
Front disc size. As near as dammit 315mm. Again, to be spot on wheel needs removing.
Disc spacing; (between the discs) Inside to inside 132mm

Rear
Outside Sprocket to out side disc. 210mm
Spindle size. 22mm measured at threaded end
Inside disc to wheel Centre. 74mm ish. and the same with sprocket . 116mm ish.
Please no rush tho .

Awkward to be absolutely bang on with dimensions without removing the wheels, but these will be very close.

[MacV2]

Front Spindle size. The only bit I can get to without removing the wheel is the wider exposed end ( not the nut end ). 25mm
Front disc size. As near as dammit 315mm. Again, to be spot on wheel needs removing.
Disc spacing; (between the discs) Inside to inside 132mm

Rear
Outside Sprocket to out side disc. 210mm
Spindle size. 22mm measured at threaded end
Inside disc to wheel Centre. 74mm ish. and the same with sprocket . 116mm ish.
Please no rush tho .

Awkward to be absolutely bang on with dimensions without removing the wheels, but these will be very close.

Very good but what about my bloody grass ?

[leevtr]

Dont talk to people with yellow bikes

[lloydie]

Thank you lee I will jot them down and have a think at the week end

[MacV2]

Dont talk to people with yellow bikes

It wont be yellow when it's ready to roll...

Mind you weather I'll be able to roll with it is open to question...

Anyway wont be much point in talking I wont be able to hear you over the noise of the mower...