Page 5 of 7

Re: My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 4:50 pm
by Kev L

Re: My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 5:21 pm
by VTRDark
It's a good idea being able to hot swap exhausts. :roll: So you can switch between the 2 into 1 back to 2 again. :thumbup: I'm quite surprised how rough the bore of the Y piece is. It looks like the rear pipe partially blocks the front. :confused

Have Fun. :thumbup:

(:-})

Re: My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 5:26 pm
by seb421
Kev L wrote:Did you see this one Lloydie -
http://www.ebay.co.uk/itm/2000-HONDA-VT ... 4d017fd7b0
6,500 my butt looks like its been ragged, dropped and painted badly including the can. no mirrors either this boy fancies his self as some roads racer

Re: My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 5:29 pm
by Kev L
I was only using it to show the 2 into 1 exhaust system. I didn't read the rest of it.

My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 5:32 pm
by lloydie
Ohhhh I like the silver wheels :)
The headers are the same as the other one side caped off lol

My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 5:34 pm
by lloydie
cybercarl wrote:It's a good idea being able to hot swap exhausts. :roll: So you can switch between the 2 into 1 back to 2 again. :thumbup: I'm quite surprised how rough the bore of the Y piece is. It looks like the rear pipe partially blocks the front. :confused

Have Fun. :thumbup:

(:-})
and that one had been cleaned up lol
They are even worse standard

Re: My 2 into 1 project now with dyno print out

Posted: Wed May 23, 2012 8:22 pm
by edds11
+1 on loydie, the outlet for my offside is like a slit about 15mm wide where its been filled with the inlet and other outlet, mr honda should be ashamed......soon to be changed though :lol: :lol: :lol: :lol: :lol: if I could write mmooohhaahhaa in a menacing way I would

Re: My 2 into 1 project now with dyno print out

Posted: Tue May 29, 2012 9:19 pm
by edds11
I can know say MMOOOHHHAAAHHHAAAAA, two silencers gone, one 60mm wyleco titanium sits in place of one of them.... sounds saweeet, goes saweeet, save up some penny's for a rolling road visit and Bob's your Uncle. :thumbup:

Re: My 2 into 1 project now with dyno print out

Posted: Tue Sep 10, 2013 12:34 pm
by Flatline
Wow, Lloydie, where can I get one of those removable thumbs from :biggrin :biggrin :biggrin
lloydie wrote:Modified my other headers today in to a 2-1 :) .i just need to get a new rear down pipe to collector gasket before I can fit them .

ImageImage

Re: My 2 into 1 project now with dyno print out

Posted: Tue Sep 10, 2013 2:51 pm
by lloydie
eBay . Very cheap from Hong Kong

Re: My 2 into 1 project now with dyno print out

Posted: Tue Sep 10, 2013 10:56 pm
by Kev L
lloydie wrote:eBay . Very cheap from Hong Kong
I think their British distributor is in Nothumberland!!!!!

Re: My 2 into 1 project now with dyno print out

Posted: Tue Sep 10, 2013 11:00 pm
by AMCQ46
Kev L wrote:
lloydie wrote:eBay . Very cheap from Hong Kong
I think their British distributor is in Nothumberland!!!!!
Very very very subtle :D :thumbup:

Re: My 2 into 1 project now with dyno print out

Posted: Tue Sep 10, 2013 11:05 pm
by Kev L
Subtle is my middle name. As much as a flying house brick!!

Re: My 2 into 1 project now with dyno print out

Posted: Tue Sep 10, 2013 11:11 pm
by lloydie
:thumbup;

Re: My 2 into 1 project now with dyno print out

Posted: Wed Sep 11, 2013 7:22 am
by Flatline
Would laugh at your witty comments but I have a thumbping headache :biggrin :biggrin :biggrin