what mesh?

[seb421]

want some race mesh to go in the rad spaces

do i go black or white on the mesh or just silver, i can't decide,

or should i paint it to match, orange to white to red?

[Martyjuk]

I painted mine satin black; goes well with the paint scheme. (Also filled the vents below the headlight and in the bellypan)
Used a sheet of mesh from B and Q, £7.50 for approx 20" x 10". Secured it with hot glue initially, but found this came loose with the temperature. Then used hi=temp silicone...this did the trick!

[seb421]

same idea i want but i plan to use a race type mesh the thicker stuff,

looks a bit to fine for my preference that from B&Q,

http://www.ebay.co.uk/itm/ALUMINIUM-RAC ... 3cbc695d7b

think i will get something like this

[VTRDark]

Black would be my choice





(:-})

[chric]

I think these would look smart on yours others wont think so but i like them
http://www.ebay.co.uk/itm/Honda-VTR-Fir ... 1e7359391e

[MacV2]

I think these would look smart on yours others wont think so but i like them
http://www.ebay.co.uk/itm/Honda-VTR-Fir ... 1e7359391e

I'm sure Dani & Casey will like them but Cal,Vale & Colin will probably take the piss behind the paddock...

[agentpineapple]

I think these would look smart on yours others wont think so but i like them
http://www.ebay.co.uk/itm/Honda-VTR-Fir ... 1e7359391e

I'm sure Dani & Casey will like them but Cal,Vale & Colin will probably take the piss behind the paddock...

chris you do like your shiny bits you magpie

and seb just stick with black fella, it will suit your bike fine, i was looking at doing the same thing, but like yourself, i found it hard to get the right size mesh for the job, good luck with it and i look forward to seeing the results....

[seb421]

I think these would look smart on yours others wont think so but i like them
http://www.ebay.co.uk/itm/Honda-VTR-Fir ... 1e7359391e

I'm sure Dani & Casey will like them but Cal,Vale & Colin will probably take the piss behind the paddock...

chris you do like your shiny bits you magpie

and seb just stick with black fella, it will suit your bike fine, i was looking at doing the same thing, but like yourself, i found it hard to get the right size mesh for the job, good luck with it and i look forward to seeing the results....

gone for the black mate

http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 0707004014

[BigVeeGrin]

I would go black, orange, white and stencil an E on somehow. Take some time but would be the nuts. I think.

Ignore anyone who says blue, like we normally do.

[tony.mon]

Another fine mesh......

[VTRDark]

....you got me into.

(:-})

[MacV2]

The mesh is fine, but wont stop mice 5mm max anything above & they will squeeze through...the b8stard !

[AMCQ46]

The mesh is fine, but wont stop mice 5mm max anything above & they will squeeze through...the b8stard !

is this linking back to the oil filter standard rating thread now? is there a ISO standard for pest filtration?

[MacV2]

The mesh is fine, but wont stop mice 5mm max anything above & they will squeeze through...the b8stard !

is this linking back to the oil filter standard rating thread now? is there a ISO standard for pest filtration?

Ha Ha, don't know about an ISO standard but pest control standard is 5mm to stop mice.

If you look at a air vent brick on your house the hole's on the front will be bigger than 5mm but it will taper down to 5mm, however that is only from about mid '60's when building reg's changed. If in doubt slap a mesh cover over it.

http://www.mousetraps.org.uk/Mouse-Trap ... ick-Covers

Above link shows old style air vent which isn't a brick at all but a cast iron vent.