WORKSHOP DAY.

[slipper 1]

Shame I will miss this as I am working overseas at the mo. How often do these happen? Just ordered CCT's from ROAS, and need someone to advise/help on fitting. the bike is still on automatic tensioners, but has quite a backfire on the over run, and I am a bit concerned that maybe the timing is already out.

[bazza696]

They backfire for a number of reasons, mine was doing it becuase of a leak at one of the exhaust joins, or running rich or lean.

I swear mine backfires in the shed even when not switch on.

[tony.mon]

We also have two bikes being fitted with manual CCT's, and both needing valve clearances checked.
So lots to watch and hopefully learn from.

See you Sat!
Tony

[Darknomad]

woohoo i have dust caps oils caps upper and lower bushes and now a hyperpro progressive spring kit im good as ready for saturday
will by manual cct at tones gaff will look at peoples braided brakes mods see whats involved
i booked friday of to do prep stuff if need be i can possibly do some shopping if people need stuff from halfords u can square up at tones likes tools fluids
i dunno what ever

[tony.mon]

Got yourself some fork oil?

[Darknomad]

yup and some stickers and a teeny pot of grease gunk all part of the spring kit 7.5 1 litre

[tinysmall]

Is there still enough room for one more bod? I need to do my CCT's.

[alec]

can someone pm me Tony's address please, i have pm'd him but doesn't seem to be about tonight and i deleted itby mistake, must be watching comic relief lol

[Kev L]

PM coming your way mate

[alec]

PM coming your way mate

thanks Kev

[Darknomad]

Im sure theirs space for more
Just cut n paste ure work plans
So it can be organized

[tinysmall]

Bazza696 (the Man for CCT's- some spare modified manual ones will be available on the day)
Jonesy (the Man for BRAKES. Any and all aspects thereof, full caliper strips etc.) Be glad to help.
Darknomad- manual ccts fitted and timed, carb balance, forks if i get springs, and valve shims if im lucky on the day to have right shims from a local shop or Tony .Mon
Alec- carb balancing & QA throttle mod (i have a pot from a 35mm film) just a general check over if poss please.i'll fit carb balancer take-offs without removing carbs (small hands!)
Elric - Making sure Yeti is working to the right specifications and tolerances.
Robwestwick
Parkergb6
Blob748
Yeti Tea making (wait 'til you see the hi-tech kettle!)
Styler4077
Wicky (front pot carb balance insert inserting - small hands required)
Matinik46
Macv2 -just joining in, and watching
Tinysmall-CCT's... was coming, then wasn't, now am again


Ummm... what time is it kicking off?

[Darknomad]

kicks off ten ish
careful of local roads
can be loose stones etc in centre

[tinysmall]

Ya muchly

[alec]

Bazza696 (the Man for CCT's- some spare modified manual ones will be available on the day)
Jonesy (the Man for BRAKES. Any and all aspects thereof, full caliper strips etc.) Be glad to help.
Darknomad- manual ccts fitted and timed, carb balance, forks if i get springs, and valve shims if im lucky on the day to have right shims from a local shop or Tony .Mon
Alec- carb balancing & QA throttle mod (i have a pot from a 35mm film) just a general check over if poss please.i'll fit carb balancer take-offs without removing carbs (small hands!)
Elric - Making sure Yeti is working to the right specifications and tolerances.
Robwestwick
Parkergb6
Blob748
Yeti Tea making (wait 'til you see the hi-tech kettle!)
Styler4077
Wicky (front pot carb balance insert inserting - small hands required)
Matinik46
Macv2 -just joining in, and watching
Tinysmall-CCT's... was coming, then wasn't, now am again


Ummm... what time is it kicking off?

10 am mate