Loud cans to replace my crumbling Danmotos?

General Bike chat
User avatar
grinner1969
Posts: 106
Joined: Sun Aug 31, 2014 12:26 am

Re: Loud cans to replace my crumbling Danmotos?

Post by grinner1969 »

Seems like I may be a little too new to come in on this Q&A, however can't help myself.
I did my usual research and found an amazing UK can company called FUEL. They have loads of choices on materials and shapes and angles at very reasonable prices. I went for a round (like the orig shape) with a slash cut, fully legal with removable baffle.Very easy fitting. They sound stunning, average at low revs, 4 thou plus they ignite, we know the v twin is the best sound ever, times it by 10, that's close to where these come in :thumbup: :thumbup: :thumbup: oh and you also get a piece of Kendel mint cake :D
User avatar
bigtwinthing
Posts: 5577
Joined: Mon Dec 17, 2012 7:52 pm
Location: Hampshire

Re: Loud cans to replace my crumbling Danmotos?

Post by bigtwinthing »

Words mean nowt without photos pls!!! imagine reading a porn mag!!! :lol:
missing the noise, not the vibes. However never say never!
User avatar
lloydie
Posts: 20923
Joined: Mon Jan 17, 2011 11:16 pm
Location: In the garage somewhere in Coventry

Re: Loud cans to replace my crumbling Danmotos?

Post by lloydie »

bigtwinthing wrote:Words mean nowt without photos pls!!! imagine reading a porn mag!!! :lol:
they have words ? ive never got past page one
User avatar
bigtwinthing
Posts: 5577
Joined: Mon Dec 17, 2012 7:52 pm
Location: Hampshire

Re: Loud cans to replace my crumbling Danmotos?

Post by bigtwinthing »

and i bet you have had it laminated!!! :lol:
missing the noise, not the vibes. However never say never!
User avatar
lloydie
Posts: 20923
Joined: Mon Jan 17, 2011 11:16 pm
Location: In the garage somewhere in Coventry

Re: Loud cans to replace my crumbling Danmotos?

Post by lloydie »

bigtwinthing wrote:and i bet you have had it laminated!!! :lol:
yep :thumbup: i laminated a dvd once but it never worked again
Virt
Posts: 6793
Joined: Wed Dec 12, 2012 12:35 pm
Location: Leicestershire

Re: Loud cans to replace my crumbling Danmotos?

Post by Virt »

lloydie wrote: yep :thumbup: i laminated a dvd once but it never worked again
Is it bad that i genuinely believe it's something you would do? :lol:


Sent from my GT-I9505 using Tapatalk
Slowly approaching the more bikes than birthdays achievement
tony.mon
Posts: 16022
Joined: Wed Jul 25, 2007 10:46 pm
Location: Norf Kent

Re: Loud cans to replace my crumbling Danmotos?

Post by tony.mon »

Them slash cuts.
Long and short in one can, depending on where you measured it.......
Taken to extreme they would be long on top and short lower down, or the other way round.
Hot air rises, and so the hotter gases given off by major revs would be at the top of the slash, so lower underneath for torque and short at the upper edge for top end horses.

There's nowt wrong with the theory, now to reduce the weight, and hacksaw at the ready, Wales weekend her we come!


It's a wonder Honda haven't twigged, but don't tell 'em, I'll make a fortune on this idea one day....
It's not falling off, it's an upgrade opportunity.
User avatar
toecutter
Posts: 33
Joined: Mon Aug 29, 2011 6:54 pm
Location: Near Inverness

Re: Loud cans to replace my crumbling Danmotos?

Post by toecutter »

Got a set of Remus grand prix cans in the end, not ran it with them on yet but going by youtube should be fine :D cheers for all advice.
Post Reply