VTR1000.ORG

... I was planning to rebuild using the seal and rebuild kits available on wemoto, david silver etc, but in looking through the forum workshop I found ... attached to the front sprocket cover and remove as one. NOTE remove the clutch lever before taking the cover off, otherwise the slave piston will start ...

... am worried that the slave is borked as it previously leaked, and I don't want to suddenly lose all my fluid whilst out on a ride. So I was planning to rebuild using the seal and rebuild kits available on wemoto, david silver etc, but in looking through the forum workshop I found this and was curious..

... port cover as the hex on the old one was almost spinning ( 4.92 from wemoto) Bled clutch Adjusted and lubed chain I didn't even get a chance to ride it as I had family stuff after and used up all my time off!

... 2015 5:13 pm Done mine recently, not that bad a job, just very fiddly, clutch cover needs to come of too, so you will also need new clutch cover ... genuine Honda clutch cover gasket, all other parts were pattern parts, wemoto sell all the parts needed, and I got the bearing of eBay, let me know if ...

Hello all, I've got a problem with my VTR1000 where the clutch drags even with the clutch lever pulled in. Its impossible to get into neutral without ... a lot of gunk, so I rebuilt both slave and master with parts from Wemoto Remove the clutch plates and clean and check Replaced the hydraulic hose ...

... No cable is gonna fit a hydraulic system... Try looking for brake & clutch LINES... Ebay as good a place to start as any... https://www.ebay.co.uk ... that.. Sorry wrong terminology! Brake hoses and clutch lines.. spoke to wemoto, there going to make some up for a good price.. if anyone else gets ...

Done mine recently, not that bad a job, just very fiddly, clutch cover needs to come of too, so you will also need new clutch cover gasket, and also ... genuine Honda clutch cover gasket, all other parts were pattern parts, wemoto sell all the parts needed, and I got the bearing of eBay, let me know if ...

... man doesn't make any money using ebay. Having a set of brake and clutch levers (for example) sitting there for a start bid of 4.99 will never ... on other trader sites to compare and price match (M&P, Demon Tweeks, Wemoto, David Silver Spares etc). Trust me Kenmoore, it'll be hard (at first ...

Does anyone know whether a clutch cable is specific to a bike, or fairly generic? It's because when I go for the adjustable clip ons, they don't come ... the cable and get some extra slack on it, I don't know. http://www.wemoto.com/bikes/suzuki/gsxr_1000_k4/04/picture/clutch_cable_-_slinky_glide ...

Replaced a bent clutch lever, I have only been meaning to do it for the last 4 and a half years!

Also praise Wemoto ordered it on Bank holiday Monday, arrived this morning!

... s it, really, any bearing shop will help if you take in the old ones. Wemoto and David Silvers have all of the mains and big end shells. All of the o ... be replaced with the engine in situ. It's the big bearing behind the clutch that definitely needs a genuine Honda replacement, in my opinion- I've ...

... out putting miles on the bike :) It's getting time now to replace the clutch though as it's slipping like a fecker. Having been quoted £230 for parts ... was wondering if anyone has had any experience of this kit: http://www.wemoto.com/bikes/honda/vtr_1000_f1_firestorm__-_sc36/01/picture/clutch_kit ...

... check the neutral switch ;-) and replace if necessary. http://images.wemoto.com/full/ELECTRICAL/10001635.jpg Description: Don't put up with the hit ... fit, and you will be glad you did, when that comforting green light comes on telling you for sure that you are in Neutral and can release the clutch!

http://www.wemoto.com/bikes/honda/vtr_1 ... rk_series/ come with the heavy duty clutch springs apparently. link