Search found 744 matches
- Sat Jan 06, 2007 2:40 pm
- Forum: Bike Chat
- Topic: rebuild progress
- Replies: 14
- Views: 1873
- Fri Jan 05, 2007 11:47 pm
- Forum: Workshop
- Topic: battery cable
- Replies: 9
- Views: 2106
- Fri Jan 05, 2007 11:47 pm
- Forum: Workshop
- Topic: battery cable
- Replies: 9
- Views: 2106
- Fri Jan 05, 2007 11:12 pm
- Forum: Bike Chat
- Topic: rebuild progress
- Replies: 14
- Views: 1873
- Fri Jan 05, 2007 11:08 pm
- Forum: Workshop
- Topic: battery cable
- Replies: 9
- Views: 2106
- Wed Jan 03, 2007 10:29 pm
- Forum: General Chat
- Topic: WARNING!!!!!.Cash card users!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- Replies: 7
- Views: 1290
- Sat Dec 30, 2006 4:36 pm
- Forum: Workshop
- Topic: pops from under tank any halp please
- Replies: 8
- Views: 1663
- Sat Dec 30, 2006 4:31 pm
- Forum: Workshop
- Topic: CCT Mounting bolt torque
- Replies: 7
- Views: 1215
do all my m6 bolts to 10 to 12Nm including cct ones. The other thing to remember is you must have a really low scale torque wrench, have 4. If I use the 4Nm to 20Nm one and set it at 12Nm and then test it against a 10Nm to 54Nm one the large one actually puts 14 to 15Nm on the bolts which would dama...
- Sat Dec 30, 2006 4:15 pm
- Forum: General Chat
- Topic: Happy birthday Cupa ( 23/12/06)
- Replies: 7
- Views: 958
- Sat Dec 30, 2006 4:13 pm
- Forum: Workshop
- Topic: Resistor help
- Replies: 13
- Views: 1744
My 1p's worth. Are you using the resistors in series to drop the voltage so that you do not pop the led's on over voltage? if so then you need the max current draw of the led's (probably between 20 and 30 mA) and the design voltage and max voltage (probably 3v and 5v respectively). Get these figures...
- Sat Dec 09, 2006 9:33 am
- Forum: Bike Chat
- Topic: Rear Suspension Linkage MOT Failure - Excessive Play
- Replies: 16
- Views: 3206
Ian, there is no rubber bush!, the outer area of each bearing is protected by a dust seal to keep the grease in and the water out but no rubber bushing at all. If one of the bearings has collapsed it would look like a bush but it's just the seal. Are they are main honda dealership? I may have a one ...
- Fri Dec 08, 2006 9:33 am
- Forum: Bike Chat
- Topic: Rear Suspension Linkage MOT Failure - Excessive Play
- Replies: 16
- Views: 3206
- Fri Dec 01, 2006 8:39 pm
- Forum: Workshop
- Topic: Front brake disc's fowling forks?
- Replies: 12
- Views: 1986
The spindle bolts up hard to the left leg (all looking from front of bike) and then the right leg floats on the spindle as it has the same bore all the way through as the spindle. Clean up the inside of the leg at the bottom and the spindle end, do up all the bolts apart from the two allen pinch bol...
- Wed Nov 29, 2006 9:16 pm
- Forum: General Chat
- Topic: What Cars do you drive
- Replies: 37
- Views: 4056
Have all the bitsto build something different, P reg chassis with logbook (sorn at mo), lc4 640 duke 2 engine with about 3k on it, lc4 400 engine with 0k on it, not proved as the 640 is. All wiring, frame needs the fuel tank lugs relocating but have had new lugs made to made the job easy, rear maste...
- Wed Nov 29, 2006 8:28 pm
- Forum: General Chat
- Topic: What Cars do you drive
- Replies: 37
- Views: 4056