Ebay Finds (unusal/cheap/rare/or just good value)

[griffo117]

these ould come in handy to someone
http://www.ebay.com.au/itm/DUAL-Switch- ... 460aa5d8ee

[benny hedges]

vtr 1000 cylinder head for sale
http://www.ebay.co.uk/itm/CYLINDER-HEAD ... 1474603%26

most probably a rear - the fronts go for double that.

[Martyjuk]

It is a rear one...cct is on the same side of the head as exhaust port...it is on the opposite side for the front head.

[VTRDark]

These could be a cheap set of later model carbs. No TPS though.
http://www.ebay.co.uk/itm/honda-vtr-100 ... 337e401e60

(:-})

[macdee]

what do ya think lads was it worth £80

http://www.ebay.co.uk/itm/221157037296? ... 1497.l2649

[lloydie]

what do ya think lads was it worth £80

http://www.ebay.co.uk/itm/221157037296? ... 1497.l2649

Yep shame I missed that :-(

[agentpineapple]

single sided swingarm already modded for a firestorm, if only i had the spare cash....
http://www.ebay.co.uk/itm/vfr-800-modif ... 2a26b27073

[lloydie]

You would still need to mod the top shock mount and the rear exhaust header .

[macdee]

what do ya think these cams any use to someone

http://www.ebay.co.uk/itm/vtr1000-fires ... 231b9140b2
http://www.ebay.co.uk/itm/vtr1000-fires ... 2c6429699e

[benny hedges]

what do ya think these cams any use to someone

http://www.ebay.co.uk/itm/vtr1000-fires ... 231b9140b2
http://www.ebay.co.uk/itm/vtr1000-fires ... 2c6429699e

why when you can have a full set of 4 off me for 30 quid lol!
then you can run 4 exhaust cams (in place of the 2 inlet cams) for a nice performance boost.

tbh the top cover should be sold with the head, not the cams, as they are machined as part of the head as a matched bearing half.

[VTRDark]

tbh the top cover should be sold with the head, not the cams, as they are machined as part of the head as a matched bearing half.

That very interesting and handy to know. Nice one

(:-})

[macdee]

why when you can have a full set of 4 off me for 30 quid lol!
then you can run 4 exhaust cams (in place of the 2 inlet cams) for a nice performance boost.
OK say some one was really stupid and didn't no what you were on about how would you explain this to the said stupid person not me its a friend of course oh and hes just asked how much performance boost you would get , honestly some people

[seb421]

are there any guides on fitting the Rear Cams to the Front? is it just a case of swap over, new shims, bolt up and go or do they need wombles about with?

[seb421]

http://www.ebay.co.uk/itm/HONDA-VTR1000 ... HOP:GB:102

[VTRDark]

Didn't mik put some exhaust cams in after his yoshi snapped before his latest purchase. I would have thought the exhaust cams would go straight in with no problems and either add or takeaway shims accordingly until they are gapped right. I think they give a little more lift than the inlet cams. Not sure on the duration. But to get the maximum benefit from them one would have to work out what the best BTDC for them is and set up with a degree wheel. Nice link on valve timing here http://www.compcams.com/Pages/416/valve ... orial.aspx

(:-})