Exhaust

[carmanbikes]

Hi All,Any one know if the after market exhaust cans made for a sp1 would fit a firestorm with different link pipes,Thanks Lee

[leevtr]

Hi All,Any one know if the after market exhaust cans made for a sp1 would fit a firestorm with different link pipes,Thanks Lee

Why are you thanking me, I haven't done anything

[lloydie]

as long as the cans have the same size fitments any will fit ie 52mm slip on
thanks lee

[edds11]

[Wicky]

Anything can be made to fit with the right size adapter or an appropriate hammer

[agentpineapple]

Hi All,Any one know if the after market exhaust cans made for a sp1 would fit a firestorm with different link pipes,Thanks Lee

wouldn't be adter some yoshi rs3's by any chance fella......

[carmanbikes]

Hi All,Any one know if the after market exhaust cans made for a sp1 would fit a firestorm with different link pipes,Thanks Lee

Why are you thanking me, I haven't done anything

No Im Lee as well

[carmanbikes]

Hi All,Any one know if the after market exhaust cans made for a sp1 would fit a firestorm with different link pipes,Thanks Lee

wouldn't be adter some yoshi rs3's by any chance fella......

Hi yes thats right but dont know if they will fit with some new link pipes

[VTRDark]

No Im Lee as well

You would have to get some link pipes made for them or change the angle of the left link pipe. And then think about how you are going to hang them as the SP hangers are further back and angled more.
http://vtr1000.org/phpBB3/viewtopic.php ... ilit=arata

(:-})

[agentpineapple]

i would imagine any storm linkpipe will fit as long as the inlet diameter is the same, normally 52mm iirc. the link pipes on those yoshi's can easily be taken off and replaced with aftermarket firestorm linkpipes, but you could make them a bit special by getting some upswept linkpipes made up, probably cost about £120, but they would look the mutts nuts.....
you can't go wrong with yoshi's i'd say they're one of the top 5 motorbike exhaust manufacturers in the world...

[carmanbikes]

i would imagine any storm linkpipe will fit as long as the inlet diameter is the same, normally 52mm iirc. the link pipes on those yoshi's can easily be taken off and replaced with aftermarket firestorm linkpipes, but you could make them a bit special by getting some upswept linkpipes made up, probably cost about £120, but they would look the mutts nuts.....
you can't go wrong with yoshi's i'd say they're one of the top 5 motorbike exhaust manufacturers in the world...

Cheers m8

[VTRDark]

SP linkpipes are a different diameter to the Storm I can't remember of the top of my head what size they are. IIRC only a couple of mm difference but there is a difference and even more so when you factor in that the storm links are designed for the gaskets. So if you was to use Storm link pipes then you would have to change the diameter at one end to fit the cans and to cut the Storm left side link pipe and alter the bend. The SP is a 45 degree and the Storm is 90 degree.

To make SP exhausts them fit hassle free then get some new link pipes made up. Using Standard Storm ones wont work without a fair bit of work. Even then they would not be as good a fit as having some custom one's made.

(:-})

[agentpineapple]

first double check and make sure the inlet pipe on the yoshi's is 52mm, otherwise your right carl, it will start to get complicated.....but if you were to get some linkpipes made up, it wouldn't matter, you'd just get them made to your spec....

[seb421]

im not to far away in Horwich if you win them you could take angle measurements from mine to get link pipes made up to look like original Yoshimura ones