Carbon fiber print under tray with modified standard tray. Used with some hole drilled in it. Cleaned ready to use. £25 plus £15 postage -SOLD
Carbon fiber print hugger. Cleaned and ready to fit. £40 plus £15 postage. - SOLD
Low level link pipes. 50.5 mm out side diameter. So the front should fit over the graphite sleeve. However because they have already been clamped they will need a bit of work to get the over a new bush. The back end should fit inside the can. The left one is spotless but the right has some small dents under the foot rest and has had a scrape underneath. This has been blended in. They are clean and should look ok fitted but they are not A1. Hence £20 plus £10 for postage
I am up loading photos. will post links soon
Can be picked up from PE12 0TP or arrange you own courier
Parts up for grabs - edited
Moderator: VTRDark
-
StuartWags
- Posts: 976
- Joined: Mon Nov 14, 2011 2:00 pm
- Location: Whaplode Drove, Lincolnshire
Parts up for grabs - edited
Last edited by StuartWags on Sat Sep 13, 2014 9:16 am, edited 2 times in total.
Re: Carbon fiber print hugger and undertay
1st dibs on the undertray & std tray...subject to having a look at the pics...StuartWags wrote:Carbon fiber print under tray with modified standard tray. Used with some hole drilled in it. Cleaned ready to use. £30 plus £15 postage
Carbon fiber print hugger. Cleaned and ready to fit. £45 plus £15 postage.
I am up loading photos. will post links soon
Can be picked up from PE12 0TP or arrange you own courier
Making up since 2007, sometimes it's true...Honest...
-
StuartWags
- Posts: 976
- Joined: Mon Nov 14, 2011 2:00 pm
- Location: Whaplode Drove, Lincolnshire
Re: Carbon fiber print hugger and undertay
Hugger
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
note the tyre rub .... pretty usual for this make
Undertray
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
Link pipes
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
note the tyre rub .... pretty usual for this make
Undertray
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
Link pipes
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
Last edited by StuartWags on Fri Sep 12, 2014 11:52 am, edited 1 time in total.
Re: Carbon fiber print hugger and undertay
No I'll pass on that thanks...
Making up since 2007, sometimes it's true...Honest...
-
StuartWags
- Posts: 976
- Joined: Mon Nov 14, 2011 2:00 pm
- Location: Whaplode Drove, Lincolnshire
Re: Parts up for grabs - edited
Link pipes added
-
StuartWags
- Posts: 976
- Joined: Mon Nov 14, 2011 2:00 pm
- Location: Whaplode Drove, Lincolnshire
Re: Parts up for grabs - edited
SOLD- I also have a Laser, oval carbon fiber exhaust system in good condition. The system is higher than the standard system and comes with its own hangers and foot rests. The hangers could do with a coat of paint. The pipes are discreetly stamped (underneath near the clamps) for racing only. They have holes for baffle but there are none with the system. They are deep, throaty (easy tiger) and pretty loud. However, i think they would pass a MOT with baffles in.
They are in good clean condition and fit directly to the headers with no graphite collars. Clamps not included
Pictures fitted and includes a video with sound.
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
Pictures removed showing comparison of hangers
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
£165 plus £15 postage
Or pick up from PE12 0TP
They are in good clean condition and fit directly to the headers with no graphite collars. Clamps not included
Pictures fitted and includes a video with sound.
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
Pictures removed showing comparison of hangers
http://s1313.photobucket.com/user/Stuar ... t=3&page=1
£165 plus £15 postage
Or pick up from PE12 0TP