Well ..with 103k on her ..time for ground up

[Elchappo76]

Geez ..would you have an idea on $$

Sent from my SM-G900I using Tapatalk

I think my front cyl head ok and vavles .will strp clean and reasemble .small relapping should be ok and seals.

Sent from my SM-G900I using Tapatalk

Hi tony . Well after pulling my case off .ive discovered more something jus not look write here ...any ideas pls .

Sent from my SM-G900I using Tapatalk

Not mention .im intrigued by the difference between front and rear cyl covers .

Sent from my SM-G900I using Tapatalk

[Elchappo76]

I think my front cyl head ok and vavles .will strp clean and reasemble .small relapping should be ok and seals.

Sent from my SM-G900I using Tapatalk

Hi tony . Well after pulling my case off .ive discovered more something jus not look write here ...any ideas pls .

Sent from my SM-G900I using Tapatalk

Sent from my SM-G900I using Tapatalk

Ok .sorry am aware that this is normal now....just took my att straightaway. .loll

Sent from my SM-G900I using Tapatalk

[AMCQ46]

i can't see anything weird, what have you spotted?>

[Elchappo76]

i can't see anything weird, what have you spotted?>

Hi ..sorry just found that its normal for that outer cogg to look abnormal to me.

Sent from my SM-G900I using Tapatalk

[Elchappo76]

I think my front cyl head ok and vavles .will strp clean and reasemble .small relapping should be ok and seals.

Sent from my SM-G900I using Tapatalk

Hi tony . Well after pulling my case off .ive discovered more something jus not look write here ...any ideas pls .

Sent from my SM-G900I using Tapatalk

Not mention .im intrigued by the difference between front and rear cyl covers .

Sent from my SM-G900I using Tapatalk

Sent from my SM-G900I using Tapatalk

[tony.mon]

Gear is normal, but it seems likely you've had a valve, valve stem seal or guide failure allowing exhaust gas into the cam cover.
Is that piece of metal you found steel or alloy?

[Elchappo76]

Gear is normal, but it seems likely you've had a valve, valve stem seal or guide failure allowing exhaust gas into the cam cover.
Is that piece of metal you found steel or alloy?

Well it looks lot lime the stainless steel from exh joint seal.

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Gear is normal, but it seems likely you've had a valve, valve stem seal or guide failure allowing exhaust gas into the cam cover.
Is that piece of metal you found steel or alloy?

Well it looks lot lime the stainless steel from exh joint seal.

Sent from my SM-G900I using Tapatalk

Yea and my thoughts as well.

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Gear is normal, but it seems likely you've had a valve, valve stem seal or guide failure allowing exhaust gas into the cam cover.
Is that piece of metal you found steel or alloy?

Well it looks lot lime the stainless steel from exh joint seal.

Sent from my SM-G900I using Tapatalk

Yea and my thoughts as well.

Sent from my SM-G900I using Tapatalk

Well i thought cant be too much to a clutch holding tool...so out with the welder again..

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Did job ..but bit bent ...should straighten on assembly.

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Question. ..i have noticed the chain here on oil pick up ..to be unexpectedly loose ..is this normal.

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Unexpectedly loose ..is this normal.

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Hi tony .. is it normally the only way to remove flywheel with the special puller i supose i have to order in...

Sent from my SM-G900I using Tapatalk

[Elchappo76]

Also is it really necessary to remove flywheel to split case to remove pistons.

Sent from my SM-G900I using Tapatalk

[AMCQ46]

yes it is normal for the old pump chain to be that loose