lower fairing

doggit · Post by **doggit** » Sat Oct 11, 2008 9:53 pm

also just bought these off e bay, and getting them in cherry red, should look ok against the black lower, and bike is red too
http://cgi.ebay.co.uk/DECALS-STICKERS-G ... =72%3A1301
carl

doggit · Post by **doggit** » Sat Oct 18, 2008 2:42 pm

just put the stickers on the lowers, not perfect but hey neither is the bike

carl

bikerpiker · Post by **bikerpiker** » Sat Oct 18, 2008 4:34 pm

It's lookin good Carl

sassage · Post by **sassage** » Sat Oct 18, 2008 4:50 pm

can someone help me out with this...found a guy that has one for sale...says it's fiberglass and i'm not sure what brand it is:

thanks

warby221 · Post by **warby221** » Sat Oct 18, 2008 8:21 pm

Doesnâ€™t matter what brand it is m8 its not a firestorm one looks like is of a CBR or something similar the top edge of the pan is to straight to fit a storm
Could be made to fit but probably not work the effort

Beamish · Post by **Beamish** » Sat Oct 18, 2008 9:45 pm

Totally agree with Warby, would not fit your Storm without some serious work. One side should have a big half round cut out.

sassage · Post by **sassage** » Sun Oct 19, 2008 12:03 am

haven't seen in person yet...but owner said it was off a Superhawk (Firestorm)...looks like it could fit against upper just not tight further back?

thanks for the responses...I just had never seen it before. Have to do some more image hunting

sassage · Post by **sassage** » Sun Oct 19, 2008 5:54 am

looks damn familiar to this, but the guy doesn't know what it is either. what you think warby and beamish?

bikerpiker · Post by **bikerpiker** » Sun Oct 19, 2008 9:39 am

I must say, looking at the side shown, it looks very similar, even the hole positions look pretty much spot on

clayderman · Post by **clayderman** » Sun Oct 19, 2008 10:31 am

Beamish wrote:One side should have a big half round cut out.

I think it has when you have a look at it it almost looks like the nearest side goes straight up but the other side has a definite curve, I'm not sure the angle helps

Beamish · Post by **Beamish** » Sun Oct 19, 2008 11:19 am

Yep I may be mistaken, I was comparing it to my Sharkskinz model. It could well be ok looking at the picture example.

clayderman · Post by **clayderman** » Sun Oct 19, 2008 11:22 am

Also that curve on the nearside is definitely closer to the the fin than the other side , it's deceptive.

warby221 · Post by **warby221** » Sun Oct 19, 2008 4:52 pm

Hummm deceptive could be

I may stand corrected there

If you getting it take the bike along just to be sure and try it up against it

sassage · Post by **sassage** » Sun Oct 19, 2008 6:32 pm

Beamish wrote:Yep I may be mistaken, I was comparing it to my Sharkskinz model. It could well be ok looking at the picture example.

it's definitely not as form fitting as the sharkskinz (which would be my first choice but it's out of my bling $$ range at the moment)

wienetta · Post by **wienetta** » Wed Nov 12, 2008 9:39 pm

I don't know what my one is, it came with the bike (The garage door is jammed shut so I'm temporarily unable to get at the bike to look). It doesn't seem to match any of yours though.