photos please help

[agentpineapple]

i tried fitting my powerbronze lowers today, and although ther'ye on they ain't on properly, i believe i have all the brackets needed, but i need to figure out what brackets go where, has anybody got a photo to show me, or could someone take a photo for me please.....
these are the fairing lowers in question........

[VTRDark]

I will wip mine off the bike tomorrow and take some pics.

(:-})

[Kev L]

They look nice Marty. If your interested I have some silver Honda decals left over from doing mine. Various sizes in the font shown below -

[agentpineapple]

those aren't mine exact ones kev, mine have been sprayed a dark met grey, i've got a pair of honda decals in the post at the mo, they're 20cm long, hopefully they're big enough, oh and they're chrome...........bling bling baby!!!!!!!!!
if they look shite i might take you up on your offer mate. also could you bring some of the ali tubing to the workshop day, the stuff that sits inside the rubber grommets when fitting the lowers/bellypan..

[Kev L]

Will do mate

[seb421]

ahhhh you bugger i had mine off today, if only you had posted before

i will wip it off again tommorow if my dads not got me doing somthing, i have the same powerbronze one as you, i also have a spare set of powerbronze fittings if required

[agentpineapple]

cheers seb
the lowers came with 3 brackets and lots of nuts and bolts, but with instructions, its a bit of a puzzle. and we didn't have enough time today to figure it out properly...
i'll have another go in the week, i've still got to do the hugger and tank......

[Wicky]

http://f.cl.ly/items/2H3Y3E2A181t3s3V1T ... nzeVTR.pdf

Marty - Check the Powerbronze fitting instructions pdf I've linked to

[pariah]

ensure you heat sheild the inner on the right side. MInes the same and when I repainted it and fitted it back on the heat from the exhaust blistered the paint so had to srtip it and repaint then line with heat sheild mattting .

[seb421]

http://f.cl.ly/items/2H3Y3E2A181t3s3V1T ... nzeVTR.pdf

Marty - Check the Powerbronze fitting instructions pdf I've linked to

I had one of those i put it in the bin, its the shittiest instructions ever wrote, I've had better from IKEA

[VTRDark]

+1 on that. It's easy enough to work out for oneself, that's what I done.

Sorry BSM forgot to take lowers off and photograph. Shall do tomorrow if still needed.

(:-})

[agentpineapple]

yes please carl, sorry to be a pain in the elbow.
parriah, both side are fully heat shielded mate
to have the lowers resprayed profesionally cost me £80 so i mage sure i fitted some heat protection.
i've left the brackets around my mates house so i'll try and sort it out for the middle of this week, i need to put alot of hours in at work this week so i doubt i'll be doing that much riding, although tuesdays weather is looking bloody good, there may have to be a ride somewhere in the offing

[seb421]

yes please carl, sorry to be a pain in the elbow.
parriah, both side are fully heat shielded mate
to have the lowers resprayed profesionally cost me £80 so i mage sure i fitted some heat protection.
i've left the brackets around my mates house so i'll try and sort it out for the middle of this week, i need to put alot of hours in at work this week so i doubt i'll be doing that much riding, although tuesdays weather is looking bloody good, there may have to be a ride somewhere in the offing

Im going in the garage now with the inspection light see if i can photograph the brackets with out taking off the lower again

will mean moving the car and moving both bikes out the garage then putting the storm in the middle its against the wall on the left so cant get to that side so easy, was hoping to do it today for you but was glued to the TV with the MotoGP then had to clean the Fish Tanks

[sirch345]

Before anyone goes taking off their lowers I've got some photo's of where the brackets go. I'll see if I can dig them out for you Marty right now.

Right I'm back again

These photo's show where the brackets bolt on for the Powebronze lower fairing.

Front of engine. L shaped bracket bolted to existing bracket.


R.H side of engine (throttle side)


Back of side stand mount (1). This bracket is the longest of all three


Back of side stand mount (2). A bit closer shot.


HTH's.
If you have any question on those photo's Marty, just fire away.



Chris.

[agentpineapple]

cheers chris
i reckon this should do the job, i'll let you know how i get on in the week matey