Page 1 of 2
helloooooooo
Posted: Fri Jun 20, 2014 10:34 pm
by Ben1211
hi this is my first visit to this forum and I just want to get any ideas on a set of hi leaval link pipes for my 98 firestorm ??????
do I need headers cos my pipes don't seam to split ?????
I think a set of hi leavel pipes and set of cans will really show my bike off to her full extent any ideas my freands
thanks
roy
Re: helloooooooo
Posted: Fri Jun 20, 2014 10:44 pm
by lloydie
Hello and welcome Roy ,
Hi level cans look good but unless you get a good st they will burn your boots .
Upload a pic when you can
Re: helloooooooo
Posted: Fri Jun 20, 2014 10:49 pm
by macdee
hello and welcome
pray tell where are you from
Re: helloooooooo
Posted: Fri Jun 20, 2014 10:53 pm
by Kev L
I've not had any issues with my Scorpion high levels. -
Re: helloooooooo
Posted: Fri Jun 20, 2014 10:54 pm
by lloydie
Kev L wrote:I've not had any issues with my Scorpion high levels. -
Yes but you have little feet !!!
Re: helloooooooo
Posted: Fri Jun 20, 2014 11:03 pm
by Kev L
What are you alluding to with that statement then young man? I'll have you know I am hung like a donkey!!!!
Re: helloooooooo
Posted: Fri Jun 20, 2014 11:17 pm
by agentpineapple
I have size 12 feet, and I've been ok with the hi level two brothers, but I've heard of people melting there boots on some lesser quality hi level linkpipes.....
oh and welcome to the forum buddy....
Re: helloooooooo
Posted: Fri Jun 20, 2014 11:19 pm
by lloydie
Kev L wrote:What are you alluding to with that statement then young man? I'll have you know I am hung like a donkey!!!!
One of them is !!! Ha ha
Like I said in my other post you need a good set of hi levels and kevs scorpion s are a good set
Re: helloooooooo
Posted: Sat Jun 21, 2014 5:46 am
by simo
Hi, Welcome to the Forum.
Re: helloooooooo
Posted: Sat Jun 21, 2014 7:19 am
by Watty
Hello and welcome
Re: helloooooooo
Posted: Sat Jun 21, 2014 8:46 am
by Ckennedy
Welcome to the forum Ben
Sent from my HTC One using Tapatalk
Re: helloooooooo
Posted: Sat Jun 21, 2014 10:19 am
by sirch345
Welcome aboard
Ben1211 wrote:do I need headers cos my pipes don't seam to split ?????
roy
The red arrow in the photo below shows where the right hand link pipe is clamped to the headers, so your standard can's (slicencer) should be clamped on at that point.
Chris.
Re: helloooooooo
Posted: Sat Jun 21, 2014 1:42 pm
by tony.mon
It's sort of self-adjusting. Once the bits of your boot heels that rest on the link pipes melts away, there's enough clearance. And your boots are lighter, too
Re: helloooooooo
Posted: Tue Jul 08, 2014 12:15 am
by VTRDark
What's the shiny metal piece on the subframe above the brake master?
Welcome to the forum roy. No need to go rushing into replacing the exhaust. Do some research first and work out what you want. Best if you can hear some cans in the flesh too.
(:-})
Re: helloooooooo
Posted: Tue Jul 08, 2014 7:51 am
by bigtwinthing
Mine have the "goose neck" link pipes and you can't move your boots back on the pegs, the only prob is that my toes of my boots rub the floor on aggressive lean angles ( not that often)
I agree they do look great. make sure that you bolt the link pipes at the bottom mounts too and not just by the rear hangers as they flex a bit.
