help help i need an answer
- northmanuk
- Posts: 134
- Joined: Wed Nov 24, 2021 6:38 pm
- Location: wales
- Contact:
help help i need an answer
i have tried twice to seal the generator side casing both times using a new gasket this is what ive done
clean both faces of joint making sure no bits of gasket are left
fit gasket over spigots
tighten bolts
fill engine with new 4 l of oil
start engine after a few mins oil comes out
repeat above cost 51.00
i have checked the crank casing and the gen case no visible damage
cheers law
clean both faces of joint making sure no bits of gasket are left
fit gasket over spigots
tighten bolts
fill engine with new 4 l of oil
start engine after a few mins oil comes out
repeat above cost 51.00
i have checked the crank casing and the gen case no visible damage
cheers law
hey mister does pi--ing on the lemon tree make em grow better
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
Re: help help i need an answer
are you missing the rubber grommet that seals the 3 yellow alternator wires into the casing? or is it not seating correctly?
AMcQ
- northmanuk
- Posts: 134
- Joined: Wed Nov 24, 2021 6:38 pm
- Location: wales
- Contact:
Re: help help i need an answer
no i got that its leaking around bottom of casing
hey mister does pi--ing on the lemon tree make em grow better
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
Re: help help i need an answer
start it to get a little heat in the casing then when it cools give it another little nip up.
the older i get,the faster i was
Re: help help i need an answer
When you levered it off, did you use a chisel or a blunt screwdriver?
It's not falling off, it's an upgrade opportunity.
Re: help help i need an answer
May be there is a hairline crack in the alternator casing?
If you have a spare from the old engine it could be worth trying that,
Chris.
If you have a spare from the old engine it could be worth trying that,
Chris.
- northmanuk
- Posts: 134
- Joined: Wed Nov 24, 2021 6:38 pm
- Location: wales
- Contact:
Re: help help i need an answer
re hammer chisel no lump hammer
i have just ordered another casing
do you know what the metal rod is for bottom left as you look at the stator
i have just ordered another casing
do you know what the metal rod is for bottom left as you look at the stator
hey mister does pi--ing on the lemon tree make em grow better
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
Re: help help i need an answer
Do you mean the spindle for the starter gearnorthmanuk wrote: ↑Tue Sep 06, 2022 4:40 pm re hammer chisel no lump hammer
i have just ordered another casing
do you know what the metal rod is for bottom left as you look at the stator
As pointed out with a screwdriver in Mac's photo below: Chris.
Re: help help i need an answer
That spindle can only be removed with a magnet.
It's not falling off, it's an upgrade opportunity.
- northmanuk
- Posts: 134
- Joined: Wed Nov 24, 2021 6:38 pm
- Location: wales
- Contact:
Re: help help i need an answer
it can be done another way but that would be telling
hey mister does pi--ing on the lemon tree make em grow better
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
no kid but it sure makes your ma mad (fastest indian)
i always wanted to ride a v twin now i got one i still cant
Re: help help i need an answer
I was trying to avoid the suggestion of taking off the casing then knocking the bike off it's sidestand...
It's not falling off, it's an upgrade opportunity.
Re: help help i need an answer
I was trying to avoid the suggestion of taking off the casing then knocking the bike off it's sidestand...
It's not falling off, it's an upgrade opportunity.